MAKER'S PLACE

 Hello Friends! Today I would familiarize you with PCB-designed MSP-430 NANO. I have designed a low-cost PCB based on an MSP430-G2553 microcontroller supporting 20 pin DIP, s. Hence, would encourage and appreciate getting your own developed as well!!!                                                     (a) MSP 430   MSP-NANO, an ultra-low-power microcontroller, featuring 16-bit RISC CPU, constant generators, and 16-bit registers together contributing to maximum code  efficiency. The device goes from low power mode to high power mode within 1  µs as allowed by DSP, a digitally controlled oscillator.    Pin Description :      Details:  Low supply-voltage range 1.8V to 3.6V Ultra-low power consumption Active mode: 230 µA at 1 MHz, 2.2 V Standby mode: 0.5 µA Off mode (RAM retention): 0.1 µA Five power-saving modes Ultra-fast wake-up from standby mode in less than 1 µs 16-bit RISC architecture, 62.5 ns instruction cycle time Basic clock module configuration Internal frequencies up to 16 MHz

The paper is about designing a Smart tube well Operating system which can control ON/OFF state of Tube Well as well as keep an eye on the amount of Electricity receiving continuously as well as to check whether the three electricity phases are available to run the 3 phase pump motor. This idea is proposed, seeing the problem of villagers who wait for electricity at night for irrigation and operate it at night time after their exhausting day in fields. We are going to build a single integrated system that will operate it automatically by setting the timer or manually by the farmer by switching it ON/OFF from his phone, when water is needed, and when to switch off the tubewell. These systems can be easily installed in tube well stations to increase the work efficiency of farmers and to avoid over-irrigation. All the data on the operation of tubewell will be stored on the cloud and the farmer will get all the notifications of operations in his cell phone. Link To Paper Project S

 Hello guys!!  This is my variable bench power supply!! it gives an output from 1.24 v -28.4 v dc , a 12 volt output and a 29 v it is a switch mode supply which makes it lighter to carry , a 24 v smps is used as initial power supply then a lm317 based variable regulated supply circuit is added to it. Upgrades----> add a precise potentiometer  to get a precise output. P.S.-- this supply also gives a constant current supply for led  and battery charging!! Components Required:-  DC-AC Converter Voltage Regulator Enclosure Switches, Potentiometer, Connectors and Indicators Lets Start Building!! First Step:- We need to convert AC-DC for that we could use various things. if we want to make "linear" power supply, we need to use a transformer or a switch mode power supply(SMPS). There are variety of transformer available in market and of different shapes (toroidal or normal). To choose a transformer, first check out your requirements as my su

Hey Guys!! In this project i have tried to make my on fidget spinner using raw aluminium and cast it into the spinner frame!! NOTE--> DO NOT TRY THIS WITHOUT ADULT SUPERVISION (as there is lot of work and you would get bored if you do it alone😆😂 we started with building a mold out of sand , we used green sand for it! then melted the aluminium , do you know on melting the all the impurities from the metal gets separated . safely pouring the liquid aluminium inside the mold , use all safety precautions ,,, melted metal is very hot and dangerous. after pouring let it dry for some minute and then break the mold. not got what i wanted as the mold contains more moisture and it broke ,,, but got a custom keyring😁😂😆

BATMAN lamp rises :p Hey guys! This is a batman lamp created by engraving batman logo on a glass plate. then a light source(led strip in my case) is provided beneath the stand which lightens up the logo  and the batman rises! 😎                                                                                     #Physics --> glass plate is a denser medium then its surroundings through which when light is subjected to pass , it reflects and refracts at the end of the plates i.e why the logo illuminates!! Engraving means the cutting of logo in the glass! P.S. I know this looks cool😎

Hello Guys!! This is a custom build of home speakers! IF YOU WANNA GET GOOD SOUND IN CHEAP PRICES😎 A custom build pair of speakers are attached to the amp module (ic tda3116d2) I am supplying an energy of 24 volts and 5 amps to the circuit through an smps and a custom bass sub woofer is also attached to the circuit !! P.S. Cause Black looks GENTLE 😆